Copyright (c) 1995, Wilko Bulte
<wilko@yedi.iaf.nl>
.
3 September 1995.
SCSI is an acronym for Small Computer Systems Interface. It is an ANSI standard that has become one of the leading I/O buses in the computer industry. The foundation of the SCSI standard was laid by Shugart Associates (the same guys that gave the world the first mini floppy disks) when they introduced the SASI bus (Shugart Associates Standard Interface).
After some time an industry effort was started to come to a more strict standard allowing devices from different vendors to work together. This effort was recognized in the ANSI SCSI-1 standard. The SCSI-1 standard (approx 1985) is now more or less obsolete. The current standard is SCSI-2 (see Further reading ), with SCSI-3 on the drawing boards.
In addition to a physical interconnection standard, SCSI defines a logical (command set) standard to which disk devices must adhere. This standard is called the Common Command Set (CCS) and was developed more or less in parallel with ANSI SCSI-1. SCSI-2 includes the (revised) CCS as part of the standard itself. The commands are dependent on the type of device at hand. It does not make much sense of course to define a Write command for a scanner.
The SCSI bus is a parallel bus, which comes in a number of variants. The oldest and most used is an 8 bit wide bus, with single-ended signals, carried on 50 wires. (If you don't know what single-ended means, don't worry, that is what this document is all about.) Modern designs also use 16 bit wide buses, with differential signals. This allows transfer speeds of 20Mbytes/second, on cables lengths of up to 25 meters. SCSI-2 allows a maximum bus width of 32 bits, using an additional cable.
Of course the SCSI bus not only has data lines, but also a number of control signals. A very elaborate protocol is part of the standard to allow multiple devices to share the bus in an efficient manner. In SCSI-2, the data is always checked using a separate parity line. In pre-SCSI-2 designs parity was optional.
In SCSI-3 even faster bus types are introduced, along with a serial SCSI bus that reduces the cabling overhead and allows a higher maximum bus length.
As you could have guessed from the description above, SCSI devices are intelligent. They have to be to adhere to the SCSI standard (which is over 2 inches thick BTW). So, for a hard disk drive for instance you do not specify a head/cylinder/sector to address a particular block, but simply the number of the block you want. Elaborate caching schemes, automatic bad block replacement etc are all made possible by this 'intelligent device' approach.
On a SCSI bus, each possible pair of devices can communicate. Whether their function allows this is another matter, but the standard does not restrict it. To avoid signal contention, the 2 devices have to arbitrate for the bus before using it.
The philosophy of SCSI is to have a standard that allows older-standard devices to work with newer-standard ones. So, an old SCSI-1 device should normally work on a SCSI-2 bus. I say Normally, because it is not absolutely sure that the implementation of an old device follows the (old) standard closely enough to be acceptable on a new bus. Modern devices are usually more well-behaved, because the standardization has become more strict and is better adhered to by the device manufacturers. Generally speaking, the chances of getting a working set of devices on a single bus is better when all the devices are SCSI-2 or newer. This does not imply that you have to dump all your old stuff when you get that shiny 2Gb disk: I own a system on which a pre-SCSI-1 disk, a SCSI-2 QIC tape unit, a SCSI-1 helical scan tape unit and 2 SCSI-1 disks work together quite happily.
As said before, SCSI devices are smart. The idea is to put the knowledge about intimate hardware details onto the SCSI device itself. In this way, the host system does not have to worry about things like how many heads are hard disks has, or how many tracks there are on a specific tape device. If you are curious, the standard specifies commands with which you can query your devices on their hardware particulars.
The advantage of intelligent devices is obvious: the device drivers on the host can be made in a much more generic fashion, there is no longer a need to change (and qualify!) drivers for every odd new device that is introduced.
For cabling and connectors there is a golden rule: get good stuff. With bus speeds going up all the time you will save yourself a lot of grief by using good material.
So, gold plated connectors, shielded cabling, sturdy connector hoods with strain reliefs etc are the way to go. Second golden rule: don't use cables longer than necessary. I once spent 3 days hunting down a problem with a flaky machine only to discover that shortening the SCSI bus by 1 meter solved the problem. And the original bus length was well within the SCSI specification.
From an electrical point of view, there are two incompatible bus types: single-ended and differential. This means that there are two different main groups of SCSI devices and controllers, which cannot be mixed on the same bus. It is possible however to use special converter hardware to transform a single-ended bus into a differential one (and vice versa). The differences between the bus types are explained in the next sections.
In lots of SCSI related documentation there is a sort of jargon in use to abbreviate the different bus types. A small list:
With a minor amount of imagination one can usually imagine what is meant.
Wide is a bit ambiguous, it can indicate 16 or 32 bit buses. As far as I know, the 32 bit variant is not (yet) in use, so wide normally means 16 bit.
Fast means that the timing on the bus is somewhat different, so that on a narrow (8 bit) bus 10 Mbytes/sec are possible instead of 5 Mbytes/sec for 'slow' SCSI. More on this later.
It should be noted that the data lines > 8 are only used for data transfers and device addressing. The transfers of commands and status messages etc are only performed on the lowest 8 data lines. The standard allows narrow devices to operate on a wide bus. The usable bus width is negotiated between the devices. You have to watch your device addressing closely when mixing wide and narrow.
A single-ended SCSI bus uses signals that are either 5 Volts or 0 Volts (indeed, TTL levels) and are relative to a COMMON ground reference. A singled ended 8 bit SCSI bus has approximately 25 ground lines, who are all tied to a single `rail' on all devices. A standard single ended bus has a maximum length of 6 meters. If the same bus is used with fast-SCSI devices, the maximum length allowed drops to 3 meters. Fast-SCSI means that instead of 5Mbytes/sec the bus allows 10Mbytes/sec transfers.
Please note that this means that if some devices on your bus use 'fast' to communicate your bus must adhere to the length restrictions for fast buses!
It is obvious that with the newer fast-SCSI devices the bus length can become a real bottleneck. This is why the differential SCSI bus was introduced in the SCSI-2 standard.
For connector pinning and connector types please refer to the SCSI-2 standard (see Further reading ) itself, connectors etc are listed there in painstaking detail.
Beware of devices using non-standard cabling. For instance Apple uses a 25pin D-type connecter (like the one on serial ports and parallel printers). Considering that the official SCSI bus needs 50 pins you can imagine the use of this connector needs some 'creative cabling'. The reduction of the number of ground wires they used is a bad idea, you better stick to 50 pins cabling in accordance with the SCSI standard.
A differential SCSI bus has a maximum length of 25 meters. Quite a difference from the 3 meters for a single-ended fast-SCSI bus. The idea behind differential signals is that each bus signal has it's own return wire. So, each signal is carried on a (preferably twisted) pair of wires. The voltage difference between these two wires determines whether the signal is asserted or de-asserted. To a certain extent the voltage difference between ground and the signal wire pair is not relevant (don't try 10 kVolts though..).
It is beyond the scope of this document to explain why this differential idea is so much better. Just accept that electrically seen the use of differential signals gives a much better noise margin. You will normally find differential buses in use for inter-cabinet connections. Because of the lower cost single ended is mostly used for shorter buses like inside cabinets.
There is nothing that stops you from using differential stuff with FreeBSD, as long as you use a controller that has device driver support in FreeBSD. As an example, Adaptec marketed the AH1740 as a single ended board, whereas the AH1744 was differential. The software interface to the host is identical for both.
Terminators in SCSI terminology are resistor networks that are used to get a correct impedance matching. Impedance matching is important to get clean signals on the bus, without reflections or ringing. If you once made a long distance telephone call on a bad line you probably know what reflections are. With 20Mbytes/sec travelling over your SCSI bus, you don't want signals echoing back.
Terminators come in various incarnations, with more or less sophisticated designs. Of course, there are internal and external variants. Almost every SCSI device comes with a number of sockets in which a number of resistor networks can (must be!) installed. If you remove terminators from a device, carefully store 'm. You will need them when you ever decide to reconfigure your SCSI bus. There is enough variation in even these simple tiny things to make finding the exact replacement a frustrating business. There are also SCSI devices that have a single jumper to enable or disable a built-in terminator. There are special terminators you can stick onto a flat cable bus. Others look like external connectors, or a connector hood without a cable. So, lots of choice as you can see.
There is much debate going on if and when you should switch from simple resistor (passive) terminators to active terminators. Active terminators contain slightly more elaborate circuit to give cleaner bus signals. The general consensus seems to be that the usefulness of active termination increases when you have long buses and/or fast devices. If you ever have problems with your SCSI buses you might consider trying an active terminator. Try to borrow one first, they reputedly are quite expensive.
Please keep in mind that terminators for differential and single-ended buses are not identical. You should not mix the two variants.
OK, and now where should you install your terminators? This is by far the most misunderstood part of SCSI. And it is by far the simplest.. The rule is: every SCSI bus has 2 (two) terminators, one at each end of the bus. So, two and not one or three or whatever. Do yourself a favour and stick to this rule. It will save you endless grief, because wrong termination has the potential to introduce highly mysterious bugs.
A common pitfall is to have an internal (flat)cable in a machine and also an external cable attached to the controller. It seems almost everybody forgets to remove the terminators from the controller. The terminator must now be on the last external device, and not on the controller! In general, every reconfiguration of a SCSI bus must pay attention to this.
What I did myself is remove all terminators from my SCSI devices and controllers. I own a couple of external terminators, for both the Centronics-type external cabling and for the internal flat cable connectors. This makes reconfiguration much easier.
The terminators discussed in the previous chapter need power to operate properly. On the SCSI bus, a line is dedicated to this purpose. So, simple huh?
Not so. Each device can provide it's own terminator power to the terminator sockets it has on-device. But if you have external terminators, or when the device supplying the terminator power to the SCSI bus line is switched off you are in trouble.
The idea is that initiators (these are devices that initiate actions on the bus, a discussion follows) must supply terminator power. All SCSI devices are allowed (but not required) to supply terminator power.
To allow for switched-off devices on a bus, the terminator power must be supplied to the bus via a diode. This prevents the backflow of current to switched-off devices.
To prevent all kinds of nastiness, the terminator power is usually fused. As you can imagine, fuses might blow. This can, but does not have to, lead to a non functional bus. If multiple devices supply terminator power, a single blown fuse will not put you out of business. A single supplier with a blown fuse certainly will. Clever external terminators sometimes have a LED indication that shows whether terminator power is present.
In newer designs auto-restoring fuses that 'reset' themselves after some time are sometimes used.
On modern devices, sometimes integrated terminators are used. These things are special purpose integrated circuits that can be dis/en-abled with a control pin. It is not necessary to physically remove them from a device. You may find them on newer host adapters, sometimes they even are software configurable, using some sort of setup tool. Consult you documentation!
Because the SCSI bus is, ehh, a bus there must be a way to distinguish or address the different devices connected to it.
This is done by means of the SCSI or target ID. Each device has a unique target ID. You can select the ID to which a device must respond using a set of jumpers, or a dip switch, or something similar. Consult the documentation of your device for more information.
Beware of multiple devices configured to use the same ID. Chaos normally reigns in this case.
For an 8 bit bus, a maximum of 8 targets is possible. The maximum is 8 because the selection is done bitwise using the 8 data lines on the bus. For wide this increases to the number of data lines.
The higher the SCSI target ID, the higher the priority the devices has. When it comes to arbitration between devices that want to use the bus at the same time, the device that has the highest SCSI ID will win. This also means that the SCSI host adapter usually uses target ID 7 (for narrow buses).
For a further subdivision, the standard allows for Logical Units or LUNs for short. A single target ID may have multiple LUNs. For example, a tape device including a tape changer may have LUN 0 for the tape device itself, and LUN 1 for the tape changer. In this way, the host system can address each of the parts of the tape unit as desired.
SCSI buses are linear. So, not shaped like Y-junctions, star topologies, cobwebs or whatever else people might want to invent.
You might notice that the terminator issue discussed earlier becomes rather hairy if your bus is not linear..
The electrical characteristics, it's noise margins and ultimately the reliability of it all are tightly related to linear bus rule.
Stick to the linear bus rule!
As stated before, you should first make sure that you have a electrically sound bus.
When you want to use a SCSI disk on your PC as boot disk, you must aware of some quirks related to PC BIOSes. The PC BIOS in it's first incarnation used a low level physical interface to the hard disk. So, you had to tell the BIOS (using a setup tool or a BIOS built-in setup) how your disk physically looked like. This involved stating number of heads, number of cylinders, number of sectors per track, obscure things like precompensation and reduced write current cylinder etc.
One might be inclined to think that since SCSI disks are smart you can forget about this. Alas, the arcane setup issue is still present today. The system BIOS needs to know how to access your SCSI disk with the head/cyl/sector method in order to load the FreeBSD kernel during boot.
The SCSI host adapter or SCSI controller you have put in your AT/EISA/PCI/whatever bus to connect your disk therefore has it's own on-board BIOS. During system startup, the SCSI BIOS takes over the hard disk interface routines from the system BIOS. To fool the system BIOS, the system setup is normally set to No hard disk present. Obvious, isn't it?
The SCSI BIOS itself presents to the system a so called translated drive. This means that a fake drive table is constructed that allows the PC to boot the drive. This translation is often (but not always) done using a pseudo drive with 64 heads and 32 sectors per track. By varying the number of cylinders, the SCSI BIOS adapts to the actual drive size. It is useful to note that 32 * 64 / 2 = the size of your drive in megabytes. The division by 2 is to get from disk blocks that are normally 512 bytes in size to Kbytes.
Right.. All is well now?! No, it isn't. The system BIOS has another quirk you might run into. The number of cylinders of a bootable hard disk cannot be greater than 1024. Using the translation above, this is a show-stopper for disks greater than 1 Gb. With disk capacities going up all the time this is causing problems.
Fortunately, the solution is simple: just use another translation, e.g. with 128 heads instead of 32. In most cases new SCSI BIOS versions are available to upgrade older SCSI host adapters. Some newer adapters have an option, in the form of a jumper or software setup selection, to switch the translation the SCSI BIOS uses.
It is very important that all operating systems on the disk use the same translation to get the right idea about where to find the relevant partitions. So, when installing FreeBSD you must answer any questions about heads/cylinders etc using the translated values your host adapter uses.
Failing to observe the translation issue might lead to un-bootable systems or operating systems overwriting each others partitions. Using fdisk you should be able to see all partitions.
You might have heard some talk of 'lying' devices? Older FreeBSD kernels used to report the geometry of SCSI disks when booting. An example from one of my systems:
aha0 targ 0 lun 0: <MICROP 1588-15MB1057404HSP4>
sd0: 636MB (1303250 total sec), 1632 cyl, 15 head, 53 sec, bytes/sec 512
Newer kernels usually don't report this information.. e.g.
(bt0:0:0): "SEAGATE ST41651 7574" type 0 fixed SCSI 2 sd0(bt0:0:0): Direct-Access 1350MB (2766300 512 byte sectors)
Why has this changed?
This info is retrieved from the SCSI disk itself. Newer disks often use a technique called zone bit recording. The idea is that on the outer cylinders of the drive there is more space so more sectors per track can be put on them. This results in disks that have more tracks on outer cylinders than on the inner cylinders and, last but not least, have more capacity. You can imagine that the value reported by the drive when inquiring about the geometry now becomes suspect at best, and nearly always misleading. When asked for a geometry , it is nearly always better to supply the geometry used by the BIOS, or if the BIOS is never going to know about this disk, (e.g. it is not a booting disk) to supply a ficticious geometry that is convenient.
FreeBSD uses a layered SCSI subsystem. For each different controller card a device driver is written. This driver knows all the intimate details about the hardware it controls. The driver has a interface to the upper layers of the SCSI subsystem through which it receives it's commands and reports back any status.
On top of the card drivers there are a number of more generic
drivers for a class of devices. More specific: a driver for
tape devices (abbreviation: st), magnetic disks (sd), cdroms (cd)
etc. In case you are wondering where you can find this stuff, it
all lives in /sys/scsi. See the man pages in section 4
for more details.
The multi level design allows a decoupling of low-level bit banging and more high level stuff. Adding support for another piece of hardware is a much more managable problem.
Dependent on your hardware, the kernel configuration file must contain one or more lines describing your host adapter(s). This includes I/O addresses, interrupts etc. Consult the man page for your adapter driver to get more info. Apart from that, check out /sys/i386/conf/LINT for an overview of a kernel config file. LINT contains every possible option you can dream of. It does not imply LINT will actually get you to a working kernel at all.
Although it is probably stating the obvious: the kernel config file should reflect your actual hardware setup. So, interrupts, I/O addresses etc must match the kernel config file. During system boot messages will be displayed to indicate whether the configured hardware was actually found.
An example loosely based on the FreeBSD 2.0.5-Release kernel config file LINT with some added comments (between []):
# SCSI host adapters: `aha', `ahb', `aic', `bt', `nca' # # aha: Adaptec 154x # ahb: Adaptec 174x # ahc: Adaptec 274x/284x/294x # aic: Adaptec 152x and sound cards using the Adaptec AIC-6360 (slow!) # bt: Most Buslogic controllers # nca: ProAudioSpectrum cards using the NCR 5380 or Trantor T130 # uha: UltraStore 14F and 34F # sea: Seagate ST01/02 8 bit controller (slow!) # wds: Western Digital WD7000 controller (no scatter/gather!). # [For an Adaptec AHA274x, 284x etc controller] controller ahc0 at isa? bio irq ? vector ahcintr # port??? iomem? [For an Adaptec AHA174x controller] controller ahb0 at isa? bio irq ? vector ahbintr [For an Ultrastor adapter] controller uha0 at isa? port "IO_UHA0" bio irq ? drq 5 vector uhaintr # Map SCSI buses to specific SCSI adapters controller scbus0 at ahc0 controller scbus2 at ahb0 controller scbus1 at uha0 # The actual SCSI devices disk sd0 at scbus0 target 0 unit 0 [SCSI disk 0 is at scbus 0, LUN 0] disk sd1 at scbus0 target 1 [implicit LUN 0 if omitted] disk sd2 at scbus1 target 3 [SCSI disk on the uha0] disk sd3 at scbus2 target 4 [SCSI disk on the ahb0] tape st1 at scbus0 target 6 [SCSI tape at target 6] device cd0 at scbus? [the first ever CDROM found, no wiring]
The example above tells the kernel to look for a ahc (Adaptec 274x) controller, then for an Adaptec 174x board, and so on. The lines following the controller specifications tell the kernel to configure specific devices but only attach them when they match the target ID and LUN specified on the corresponding bus.
Wired down devices get 'first shot' at the unit numbers so the first non 'wired down' device, is allocated the unit number one greater than the highest 'wired down' unit number for that kind of device. So, if you had a SCSI tape at target ID 2 it would be configured as st2, as the tape at target ID 6 is wired down to unit number 1. Note that wired down devices need not be found to get their unit number. The unit number for a wired down device is reserved for thet device, even if it is turned off at boot time. This allows the device to be turned on and brought on-line at a later time, without rebooting. Notice that a device's unit number has no relationship with it's target ID on the SCSI bus.
Below is another example of a kernel config file as used by FreeBSD version < 2.0.5. The difference with the first example is that devices are not 'wired down'. 'Wired down' means that you specify which SCSI target belongs to which device.
A kernel built to the config file below will attach
the first SCSI disk it finds to sd0, the second disk to sd1
etc. If you ever removed or added a disk, all other devices
of the same type (disk in this case) would 'move around'.
This implies you have to change /etc/fstab each time.
Although the old style still works, you are strongly recommended to use this new feature. It will save you a lot of grief whenever you shift your hardware around on the SCSI buses. So, when you re-use your old trusty config file after upgrading from a pre-FreeBSD2.0.5.R system check this out.
[driver for Adaptec 174x]
controller ahb0 at isa? bio irq 11 vector ahbintr
[for Adaptec 154x]
controller aha0 at isa? port "IO_AHA0" bio irq 11 drq 5 vector ahaintr
[for Seagate ST01/02]
controller sea0 at isa? bio irq 5 iomem 0xc8000 iosiz 0x2000 vector seaintr
controller scbus0
device sd0 [support for 4 SCSI harddisks, sd0 up sd3]
device st0 [support for 2 SCSI tapes]
[for the cdrom]
device cd0 #Only need one of these, the code dynamically grows
Both examples support SCSI disks. If during boot more devices of a specific type (e.g. sd disks) are found than are configured in the booting kernel, the system will simply allocate more devices, incrementing the unit number starting at the last number 'wired down'. If there are no 'wired down' devices then counting starts at unit 0.
Use man 4 scsi to check for the latest info on the SCSI
subsystem. For more detailed info on host adapter drivers use eg
man 4 aha for info on the Adaptec 154x driver.
Experience has shown that some devices are slow to respond to INQUIRY commands after a SCSI bus reset (which happens at Boot time). An INQUIRY command is sent by the kernel on boot to see what kind of device (disk, tape, cdrom etc) is connected to a specific target ID. This process is called device probing by the way.
To work around this problem, FreeBSD allows a tunable delay time before the SCSI devices are probed following a SCSI bus reset. You can set this delay time in your kernel configuration file using a line like:
options "SCSI_DELAY=15" #Be pessimistic about Joe SCSI deviceThis line sets the delay time to 15 seconds. On my own system I had to use 3 seconds minimum to get my trusty old CDROM drive to be recognized. Start with a high value (say 30 seconds or so) when you have problems with device recognition. If this helps, tune it back until it just stays working.
Although the SCSI standard tries to be complete and concise, it is a complex standard and implementing things correctly is no easy task. Some vendors do a better job then others.
This is exactly where the 'rogue' devices come into view. Rogues are devices that are recognized by the FreeBSD kernel as behaving slightly (...) non-standard. Rogue devices are reported by the kernel when booting. An example for two of my cartridge tape units:
Feb 25 21:03:34 yedi /386bsd: ahb0 targ 5 lun 0: <TANDBERG TDC 3600 -06:> Feb 25 21:03:34 yedi /386bsd: st0: Tandberg tdc3600 is a known rogue Mar 29 21:16:37 yedi /386bsd: aha0 targ 5 lun 0: <ARCHIVE VIPER 150 21247-005> Mar 29 21:16:37 yedi /386bsd: st1: Archive Viper 150 is a known rogue
For instance, there are devices that respond to all LUNs on a certain target ID, even if they are actually only one device. It is easy to see that the kernel might be fooled into believing that there are 8 LUNs at that particular target ID. The confusion this causes is left as an exercise to the reader.
The SCSI subsystem of FreeBSD recognizes devices with bad habits by looking at the INQUIRY response they send when probed. Because the INQUIRY response also includes the version number of the device firmware, it is even possible that for different firmware versions different workarounds are used.
This scheme works fine, but keep in mind that it of course only works for devices that are KNOWN to be weird. If you are the first to connect your bogus Mumbletech SCSI cdrom you might be the one that has to define which workaround is needed.
Most, but not all, SCSI host adapters are bus mastering controllers. This means that they can do I/O on their own without putting load onto the host CPU for data movement.
This is of course an advantage for a multitasking operating system like FreeBSD. It must be noted however that there might be some rough edges.
For instance an Adaptec 1542 controller can be set to use different transfer speeds on the host bus (ISA or AT in this case). The controller is settable to different rates because not all motherboards can handle the higher speeds. Problems like hangups, bad data etc might be the result of using a higher data transfer rate then your motherboard can stomach.
The solution is of course obvious: switch to a lower data transfer rate and try if that works better.
In the case of a Adaptec 1542, there is an option that can be put into the kernel config file to allow dynamic determination of the right, read: fastest feasible, transfer rate. This option is disabled by default:
options "TUNE_1542" #dynamic tune of bus DMA speed
Check the man pages for the host adapter that you use. Or better still, use the ultimate documentation (read: driver source).
The following list is an attempt to give a guideline for the most common SCSI problems and their solutions. It is by no means complete.
/sys/scsi/scsidebug.h.
If it probes but just doesn't work, you can use the
scsi(8) command to dynamically set a debug level to
it in a running kernel (if SCSIDEBUG is defined).
This will give you COPIOUS debugging output with which to confuse
the gurus. see man 4 scsi for more exact information.
Also look at man 8 scsi.
If you intend to do some serious SCSI hacking, you might want to have the official standard at hand:
Approved American National Standards can be purchased from ANSI at 11 West 42nd Street, 13th Floor, New York, NY 10036, Sales Dept: (212) 642-4900. You can also buy many ANSI standards and most committee draft documents from Global Engineering Documents, 15 Inverness Way East, Englewood, CO 80112-5704, Phone: (800) 854-7179, Outside USA and Canada: (303) 792-2181, FAX: (303) 792- 2192.
Many X3T10 draft documents are available electronically on the SCSI BBS (719-574-0424) and on the ncrinfo.ncr.com anonymous ftp site.
Latest X3T10 committee documents are:
On Usenet the newsgroups comp.periphs.scsi and comp.periphs are noteworthy places to look for more info. You can also find the SCSI-Faq there, which is posted periodically.
Most major SCSI device and host adapter suppliers operate ftp sites and/or BBS systems. They may be valuable sources of information about the devices you own.